Serpentine Belt Diagram: replacement serpentine belts auxiliary units Lexus RX300 .

______________________________________________________

Compact off-road car Lexus RX-300 of a category "lux" has appeared in the market in 1998.On an integral body with front and rear stretchers independent suspensions of type the Poppy-ferson with antiroll bars are established. A steering - rack , with the hydraulic booster with variable factor of strengthening. In addition the car is equipped by stabilisation system stability(VSC). Braking system - hydraulic, two-planimetric with the vacuum servo. Brake gears of all wheels the disk; front brake plates ventilated. Unlike variants for the European market on which the parking brake is resulted by the lever located between seats, on models for America the foot drive gear of a parking brake is applied. Base complete set Lexus RX-300 rather rich, but also the list of additions to it enough big, therefore the most popular additions are shown in two "packages" - «Premium» and «Limited», - which provide presence of the leather inner trim decorated by a nut tree, the powerful filter of system of ventilation of interior, and also high quality audiosystem Nacamichi. By request interior it is possible to complete with CD-changer on 6 disks and "neosticking together" mirrors.

During to replacement multiridge serpentine belt the new should be the same size, as well as old.

At installation new serpentine belt it is necessary to pay attention that serpentine belt adjoins closely to pulleys and it is not displaced rather their butts. If multiridge serpentine belt acts in film not for the purpose of its replacement, remember or note a direction of its movement that then to establish serpentine belt the correct party. Use Serpentine belt Diagram.

PERFORMANCE ORDER
1. Give swing and fixing bolts serpentine belt the generator and compressor K/V. Slacken a tension serpentine belt an adjusting bolt also remove serpentine belt.



Fig.1. Replacement serpentine belt auxiliary units Lexus RX300
1 - the Swing bolt
2 - the Fixing bolt
3 - the Adjusting bolt



2. Establish new serpentine belt the generator and compressor K/V in sequence, return to removal. Check up a tension serpentine belt.
3. Give swing and adjusting bolts serpentine belt a drive gear of pump GUR and remove serpentine belt.


Fig.2. Replacement serpentine belt auxiliary units Lexus RX300
1 - the Swing bolt
2 - the Adjusting bolt
3 - the Adjusting buckle





4. Establish new serpentine belt pump GUR in sequence, return to removal. Use Serpentine belt Diagram. Check up a tension serpentine belt.

______________________________________________________


The information was given by beltdrive.50webs.com
______________________________________________________

Serpentine Belt Diagram: check serpentine belts auxiliary units Lexus RX300 .

______________________________________________________

Compact off-road car Lexus RX-300 of a category "lux" has appeared in the market in 1998. On considered models establish engine V6 of 3.0 l. Capacity of 223 h.p. the Four-stage automatic transmission (АТ), united with an interaxle differential by means of viscous clutches, provides a constant all wheel drive with equal distribution of a twisting moment between shafts. The rear bridge is equipped by differential with viscous a clutch of restriction of slippage. The models intended for the American market, can have a drive gear only on front wheels, on these models is applied modified 4-step АТ (without an interaxle differential). Serpentine Belt Diagram tells about condition check serpentine belts Lexus RX300 . Too low tension serpentine belt conducts to its raised deterioration or fast failure. At too high tension there can be damages of bearings of the units, resulted to data belt. It is necessary to check periodically a condition serpentine belt, and at detection of defects, to replace belt.
PERFORMANCE ORDER
1. Fingers walk on all length serpentine belt, feeling it on presence of cracks and stratifications. Also check up, whether is not present on serpentine belt attritions and polish to shine of sites. Serpentine belt it is necessary to inspect from both parties that means its necessity twisting. Be in passing convinced of absence of a rust, cracks and agnails on pulleys. On a work face serpentine belt presence of superficial perpendicular cracks is supposed. If these cracks do not overstep the bounds of one edge and not so deep, to replace serpentine belt there is no necessity.






Fig.1. Condition check serpentine belts auxiliary units Lexus RX300
Deterioration of edges of edges serpentine belt






Fig.2. Condition check serpentine belts auxiliary units Lexus RX300
Cross-section cracks (D) from an underside serpentine belt and bond liftoff edges (E) -







Fig.3. Condition check serpentine belts auxiliary units Lexus RX300
drawing waste lateral edges (F), cracks (H) and bond liftoff lateral edges (G)






Fig.4. Condition check serpentine belts auxiliary units Lexus RX300
Separation of edges (J), cracks (K)




2. Make sure of correctness of position serpentine belt on pulleys, using Serpentine belt Diagram.






Fig.5. Condition check serpentine belt auxiliary units Lexus RX300




3. Check up a tension serpentine belt by means of the special adaptation and compare the received results to requirements of Specifications Serpentine belt Diagram.


Тension serpentine belt compressor K/V and the generator it is necessary to check on a site between them.

______________________________________________________


The information was given by beltdrive.50webs.com
______________________________________________________